Cover design
Size a paperback cover and spine
Use the final page count and paper choice to place the back, spine and front on one cover.
Start with the final interior PDF
Write down the finished page dimensions, the total number of PDF pages, the binding and the paper you intend to order. A 160-page double-sided interior has 80 leaves. Enter 160 in a calculator that asks for pages. Paper thickness affects the spine, and two papers with the same weight can have different thicknesses.
Keep the specification beside your cover artwork. Record whether the dimensions refer to one trimmed page, the flat trimmed cover or the artwork including bleed. A designer receiving only “A5, 160 pages” still needs the stock and binding to place the spine folds. If the printer has already supplied a template for that exact combination, check its stated dimensions before making a custom canvas.
Read the cover as a flat sheet
For a left-to-right paperback, the back cover sits on the left, the spine in the centre and the front on the right. A right-to-left book opens the other way. Confirm the cover orientation for that binding before placing the artwork. Use a case-specific template from the printer for a hardcover.
Fold a sheet of scrap paper around a book that opens in the intended direction. Write FRONT on the closed cover and mark the top edge across both panels. Now unfold it. Compare the position of your title, author photograph and barcode with those panels on screen. This is especially helpful when one illustration runs all the way from the back panel onto the front.
Lay out an A5 cover from a confirmed spine
Suppose the printer confirms an 8 mm spine and requests 3 mm of bleed around the outside of an A5 paperback. The flat trimmed width is 148 + 8 + 148 = 304 mm. Adding 3 mm on both outside edges gives a file width of 310 mm. The file height is 210 + 3 + 3 = 216 mm. In this example the spine measurement comes from the printer. Confirm it for each combination of page count, stock and binding.
For a left-to-right book, measure from the left edge of that 310 mm file. The back begins at x = 3 mm and ends at x = 151 mm. The spine runs to x = 159 mm, so its centre is x = 155 mm. The front ends at x = 307 mm. Print a strip through the middle at actual size, fold it on the two spine guides and check the title position. If the stock changes, replace the spine measurement and reposition the front as a panel. Enlarging the whole design would change both trim panels.
| Guide | From the left file edge |
|---|---|
| Back outer trim | 3 mm |
| Back meets spine | 151 mm |
| Spine centre | 155 mm |
| Spine meets front | 159 mm |
| Front outer trim | 307 mm |
Separate trim, bleed and safe area
Trim marks show the finished edge. Extend backgrounds that touch the edge into the bleed so a small cutting shift still leaves colour at the edge. Keep letters, faces, logos and the barcode inside the safe area. For example, a front-cover photograph can cross the trim line while the author’s name stays well inside it.
View the artwork once with the guides visible, then again with everything outside the trim hidden. In the cropped view, is the top of a person’s head in the right place? Does the author’s surname sit uncomfortably close to the fold? In the full view, take the background across the bleed on all four outside edges. Use the clearances on the actual template for small lettering and the barcode.
Recheck the cover after any page change
Download a template for the current specification and place it at actual size. Centre spine text within the spine guides if the printer confirms there is enough room. Hide the guide layer on your final artwork. Confirm the stock-specific spine measurement before approving the cover for production.
Send a screenshot of the design on the template for discussion, and keep the print artwork as its own export. Open the print PDF, inspect its page dimensions and zoom in on the title and spine. Compare it with the marked dummy. A print operator should be able to identify the exact interior that belongs with that cover from the filenames alone.
Try it with your book
Fold a rough paper cover around a book on your desk. Mark the front, back and spine while it is closed. Open it flat and use it as an orientation check beside your cover file.